How to Frag Zoanthids Safely
Share
Quick answer
To frag zoanthids, wear gloves and eye protection first, because zoas and palys can carry palytoxin. Then cut a small group of polyps free with a little rock or base attached, and glue that piece to a frag plug. Cut as little tissue as you can.
| Who | Reef keepers with a zoa colony on a rock, plug or disc who are ready to split it, and who can wear gloves and eye protection. |
|---|---|
| What | Separating a group of polyps from the colony and gluing it to a new plug. |
| When | When the colony is healthy and has spread, and when you have time to set up first. Soft corals handle time out of water well, so you do not have to rush. |
| Where | At a well lit, organized work area with your tools ready, not over your tank. |
| Why | To control a colony, spread it to a new spot, or trade or give a frag away. |
Safety first: palytoxin
Bulk Reef Supply says zoas and palys can contain a toxin that is very dangerous if it enters your blood stream. Reef Builders says zoanthids are toxic and should be handled with caution. Both tell you to wear eye protection and gloves. Bulk Reef Supply adds that this applies to handling the coral in the water and out of it.
Get gloves that fit well. Keep clean saltwater nearby. The sources we read do not give first aid steps, so this guide does not either. Do not frag zoanthids without protection.
What you need
- Gloves and eye protection
- Bone cutters or a stony coral cutter, plus scissors and forceps
- A razor blade
- Coral glue
- Frag plugs, discs or rock rubble
- A towel, and clothes you do not mind getting glue on
Rinse metal tools in fresh RO water after each use to slow rust. For a big rock covered in zoas, Reef Builders says a diamond band saw is the easiest way to make many frags. It also warns the saw could cost you a couple of zoanthids.
How to frag zoanthids, step by step
- Set up. Lay out your tools, glue and plugs. Good light helps.
- Put on protection. Gloves and eye protection go on before the coral comes out of the water.
- Pick your polyps. Follow the natural breaks in the colony. Sources say this makes frags easier to cut and helps them heal faster.
- Cut. One method: use a razor blade to slice the tissue around the polyps you want, then trace the razor line with coral cutters. The zoanthids should break off easily. Another method: cut into the rock under the polyp so it comes away with a small piece of rock. For a whole colony, break it up with bone cutters, then trim smaller frags with scissors and leave some base on each.
- Dip. Bulk Reef Supply says to dip new frags in iodine before you attach them to a plug. Follow the label of the dip you use. Our dipping guide covers the basics.
- Glue. Soak the plug, then dry the plug and the bottom of the frag. Add a small amount of glue and set the frag on top. Reef Builders says the glue cures in a few seconds.
- Return it to the tank. Use a baster to blow off mucus the coral has made.
Use less glue than you think you need. Bulk Reef Supply puts it as "less is always more." For plug choices, see our frag plugs and plug holders.
Plug, disc or rubble
Bulk Reef Supply says plugs suit organizing and selling. Discs suit frags you plan to keep propagating. Rubble suits putting frags back into a display.
Aftercare
Put new frags in a dimmer spot at first. Zoas and palys react to sudden light changes, so move them up slowly. Keep water parameters stable. Feed small-particle foods such as phytoplankton or liquid foods.
Sources differ on flow. One says smaller polyps do better in medium to low flow and larger polyps in stronger flow, and that too much flow makes them close. Another says to put fresh frags in high flow. Start in the middle and watch the polyps. Open, colorful polyps that keep spreading are a good sign. Bulk Reef Supply also suggests running carbon or doing a water change after you frag.
Mistakes to avoid
- Skipping gloves or eye protection.
- Cutting through more tissue than you need.
- Using too much glue.
- Putting a frag straight into bright light.
If you are new to cutting coral, start with the general guide to fragging coral at home.
Questions people ask
Do I really need gloves to frag zoas?
Yes. Every source we read for this guide says to wear gloves and eye protection, because zoas and palys can contain palytoxin.
Can I use scissors instead of cutters?
Bulk Reef Supply says to break up the colony with bone cutters, then trim smaller frags with scissors. Reef Builders uses a razor blade and coral cutters.
When is a frag ready to share?
Reef Builders says once the frag grows new tissue and polyps, it is ready to sell, trade or give away.
Do zoas need to be on a plug?
No. A plug is one option. Discs and rubble also work, depending on what you plan to do with the frag.
Gear for this job
Somewhere to put your new zoa frags
The Nexus Coral Sphere page lists zoanthids as a coral to use on it and says it holds 10 standard frag plugs. The Nexus Nano holds 5 standard frag plugs and locks each plug in place.
Shop Frag Plugs and Plug HoldersKeep reading: How to Frag Coral at Home: A Beginner's Guide · How to Mount Coral the Right Way · How to Dip Corals Before They Go in Your Tank



