XL frag rack under blue light

Frag Tank Setup: What You Need

Quick answer

A frag tank setup needs a wide, shallow tank, even lighting, steady random flow, clean stable water and something to hold the frags, such as a frag rack or egg crate. Keep the tank simple. A bare bottom, a way to test and top up your water, and a plan to keep it separate from sick fish all make upkeep easier.

Who Reef keepers who want a place to grow, hold or sell frags apart from the display tank.
What A tank built for coral frags: light, flow, filtration, water testing and racks.
When Before you buy frags to grow, or when your display tank runs out of room.
Where Anywhere you have floor or shelf space. Some keepers plumb it to the display sump.
Why Frags grow faster and are easier to handle in a tank made for them.

Frag tank setup, step by step

  1. Pick a wide, shallow tank. Bulk Reef Supply says any size works, but you want it long and wide to hold as many frags, racks or egg crate as you can. Depth can be as low as 6 inches. Its example is a 3 foot by 2 foot by 6 inch tank, which it says can hold potentially hundreds of frags. Gensou, an aquascaping retailer, also says shallow tanks outperform tall ones for frag work.
  2. Choose open and rimless if you can. Bulk Reef Supply likes an open top so you can lift egg crate in and out. Shallow acrylic may need a euro brace to stop bowing.
  3. Set up filtration. Use an all-in-one tank with a rear chamber, or plumb an overflow to a sump. The article suggests filter socks or pads for mechanical filtration, ceramics for biological, and carbon and GFO for chemical. A skimmer is optional. It can help with pH through oxygenation, but may also remove coral food and trace elements.
  4. Light the whole tank evenly. Aim for no hot spots or shadows. T5 fluorescent lighting and rows of linear LEDs are both called good choices. Mount spotlight style LEDs higher for wider spread.
  5. Add flow. Use wide outlet wave pumps for even movement without blasting frags or leaving dead spots. Gyre pumps suit long, shallow tanks. Gensou prefers a pump with a random mode and warns against laminar flow aimed straight at healing frags.
  6. Plan for testing and dosing. Hard coral frags use up buffers and elements quickly, so Bulk Reef Supply says you need auto-dosing or a calcium reactor. Test alkalinity, calcium, magnesium, nitrate and phosphate.
  7. Add racks. Bulk Reef Supply says to use frag racks or egg crate to hold the frags.

Light for a frag tank

Match what the frags had before. Bulk Reef Supply says to use a PAR meter to match the light frags got in the display, especially if you are moving them up from a deeper tank. Gensou gives one set of numbers: 150 to 250 PAR at the frag surface, a 10 hour photoperiod with one hour ramps up and down, and an LED panel mounted 15 to 20 cm above the water. That is one source, so treat it as a starting point and check it with a meter.

Water in a frag tank

Gensou lists alkalinity at 7.5 to 8.5 dKH, calcium at 400 to 420 ppm and magnesium at 1,300 to 1,350 ppm, and says RODI water should read 0 TDS before you mix salt. Bulk Reef Supply tells you what to test but gives no target numbers. For a wider set of ranges, see our guide to reef tank parameters.

If the tank runs on its own, Gensou suggests 20 percent water changes each week with the same salt mix as your display. Its maintenance list is weekly siphoning, filter floss changes, RODI top-offs and alkalinity and calcium tests, plus a monthly glass scrub and pest check.

Racks and plugs

Bulk Reef Supply says to use racks or egg crate, and to go bare-bottom the tank instead of using sand, which is easier to clean and does not trap detritus. Gensou raises egg crate 8 to 10 cm off the floor on PVC legs so detritus settles and can be siphoned. It also lists acrylic magnetic racks as an alternative, and says to space frags at least 3 cm apart.

Rhino's Reef makes several racks. The XL Frag Rack is 12 inches long and 3 inches wide, with 63 holes for standard frag plugs and a magnetic hold on glass or acrylic. The Nano Square Frag Rack is made for small tanks, and its page says it lets enough water circulation through to prevent debris build-up. The Smash Frag Rack lists coral propagation and grow-out setups among its uses. The Egg Crate Stands come in 1 to 6 inch heights in the size options. Browse frag plugs and plug holders for the plugs themselves.

Bulk Reef Supply also says frags should base down on a plug quickly, ideally faster than they would in a display. See how to mount coral for the steps.

What to leave out

  • Decor. Bulk Reef Supply says to keep decor out of the tank.
  • Refugiums and algae scrubbers. The article calls them unnecessary because there is little nitrate to feed them.
  • Fish medications. Do not use the frag tank as a hospital tank, since fish-only medications and inverts do not mix.

The same article says to add fish and inverts only if they serve a purpose, such as a tang or foxface to control algae in a large frag tray.

Questions people ask

How deep should a frag tank be?

Shallow works. Bulk Reef Supply says as little as 6 inches. Gensou says to keep SPS grow-outs under 30 cm deep.

Do I need a skimmer on a frag tank?

No. Bulk Reef Supply calls skimmers optional and notes they may remove coral food and trace elements.

Do I need a sump?

No. An all-in-one tank with a rear filter chamber works. A sump with an overflow is the other option.

Should I use sand?

Bulk Reef Supply recommends a bare bottom, which is easier to clean and does not trap detritus.

Gear for this job

Racks to hold your frags

Pick a rack by tank size. The XL has 63 holes, the Nano Square is made for small tanks, and the Smash Frag Rack lists grow-out among its uses.

Shop Frag Racks
Back to blog