Red Hanna checker organizer with checker and cuvettes

Reef Tank Parameters: The Numbers to Test and Target

Quick answer

Reef tank parameters are the water numbers you test: salinity, temperature, pH, alkalinity, calcium, magnesium, nitrate and phosphate. The sources we opened agree on the broad ranges and differ at the edges, so pick one range for your tank and keep it steady. Slow, small changes matter more than chasing an exact number.

Who Anyone with a saltwater reef tank, from a first nano to a mixed reef.
What Eight numbers: salinity, temperature, pH, alkalinity, calcium, magnesium, nitrate and phosphate. Ammonia and nitrite should read near zero.
When Weekly for most numbers once the tank has cycled. A new tank needs ammonia, nitrite and nitrate checks three or more times a week.
Where At home, with the same kit or meter each time. Red Sea also says to test calcium at the same time of day.
Why Corals and fish react to swings. Red Sea caps how much alkalinity and calcium to raise in a day to prevent stress to the corals.

Reef tank parameters at a glance

These are the ranges each source gives. Where they differ, both are shown.

  • Salinity: specific gravity 1.023 to 1.025 (Reef Builders, 2020). 35 ppt, or 1.026 specific gravity (Bulk Reef Supply). 33 to 35 PSU depending on tank type (Red Sea).
  • Temperature: 76 to 80 F (24 to 26 C) for most reef fish (Reef Builders, 2020). 78 to 84 F, average about 81 F (Reef Builders, 2008).
  • pH: 7.9 to 8.3, ideally read with an electronic probe (Reef Builders, 2008). The other sources give no pH range.
  • Alkalinity: 8 to 12 dKH (Reef Builders 2020, Bulk Reef Supply). 8 to 11 dKH (Reef Builders, 2008). 7 to 12 dKH in Red Sea's table, depending on tank type and goal.
  • Calcium: 380 to 450 ppm (Reef Builders 2020, Bulk Reef Supply). 390 to 450 ppm (Reef Builders, 2008). 410 to 465 ppm in Red Sea's table.
  • Magnesium: 1200 to 1400 ppm (Reef Builders 2020, Bulk Reef Supply). 1350 to 1400 ppm (Reef Builders, 2008).
  • Phosphate: 0.01 to 0.03 ppm (Reef Builders 2020, Bulk Reef Supply). 0.03 ppm (Reef Builders, 2008).
  • Nitrate: 1 to 10 ppm (Bulk Reef Supply). 10 ppm or less (Reef Builders, 2008). Near zero (Reef Builders, 2020).
  • Ammonia and nitrite: zero or near zero once the tank has cycled.

Why the ranges differ

Red Sea does not give one set of numbers. Its table changes the target by tank type and by goal. A mixed reef aiming for great growth and great color sits at 34 PSU, 450 ppm calcium and 11.5 dKH. A ULNS tank aiming for color sits at 33 PSU, 410 ppm and 7 dKH. A tank for fast growth sits at 35 PSU, 465 ppm and 12 dKH.

The Reef Builders 2008 article is older, and it gives a warmer temperature range than the 2020 article. When you see two ranges, pick the one that fits your corals, and ask the maker of your salt or supplements what they target.

Test salinity first

Red Sea says to check salinity before any other test, and to wait 10 minutes after you adjust it. Salinity moves calcium. Red Sea gives an example: a 1 PSU rise from evaporation raises calcium by about 13 ppm. If you test calcium first and your salinity has crept up, you may chase a number that was never wrong.

Change numbers slowly

Stable water is the point of testing. Red Sea sets a daily maximum for corals: calcium up by 20 ppm and alkalinity up by 1.4 dKH. If you need a bigger change, spread it over a few days. Red Sea also says to test again after a water change and adjust if needed.

Match the units on your kit

Alkalinity shows up in three units. Hanna's HI772 manual gives the conversion: 1 dKH equals 17.86 ppm CaCO3, or 0.358 meq/L. Salinity can be ppt, PSU or specific gravity. Check the unit before you compare a reading to a range.

If you test with Hanna Checkers, our Hanna checker organizers give the kits and cuvettes a home on your bench.

How often to test

Reef Builders (2020) says a weekly test is enough after the tank has cycled, and that new tanks need testing three or more times a week for ammonia, nitrite and nitrate. Its phosphate advice is weekly. Red Sea says weekly monitoring helps, tests alkalinity every 2 to 3 weeks while dosing, and suggests a logbook of weekly measurements. Write every result down. A trend tells you more than one number.

Questions people ask

What is the most important reef tank parameter?

None of the sources we opened ranks them. Reef Builders (2020) calls salinity and temperature problems among the most preventable, and Red Sea checks salinity before every other test.

What alkalinity should a reef tank have?

Most sources we opened say 8 to 12 dKH. Red Sea's table runs from 7 to 12 dKH, depending on the type of tank.

Is zero nitrate good for a reef?

The sources disagree. Reef Builders (2020) says near zero. Bulk Reef Supply lists 1 to 10 ppm. Reef Builders (2008) says 10 ppm or less.

Do I need a pH probe?

Reef Builders (2008) says to use an electronic probe if possible. The other sources give no pH advice.

Gear for this job

A tidy bench for reef testing

The Hanna Checker Organization System is a 6-piece set of custom 3D-printed stands and organizers for Hanna testing gear. CuveDry holds Hanna Checker cuvettes upright so they can air dry.

Shop Hanna checker organizers
Back to blog