Red Hanna checker organizer with checker and cuvettes

Hanna Calcium Checker Instructions, Step by Step

Quick answer

Hanna calcium checker instructions come down to two cuvette stages. In the first you add reagent A to deionized water and zero the checker. In the second you add 0.1 mL of tank water and one packet of reagent B, shake, and read calcium in ppm. These steps are for the Hanna HI758, using Hanna's 02/22 manual.

Who Reef keepers with a Hanna Marine Calcium Checker HC, model HI758.
What A colorimetric test that reads calcium from 200 to 600 ppm in 1 ppm steps.
When On your regular testing day. One reef retailer says to test calcium weekly at minimum, and after you add or remove livestock.
Where At your bench, with a clean, dry cuvette and calcium-free water for the first stage.
Why Red Sea ties coral growth to calcium uptake, so a regular reading shows how fast your tank uses it.

What you need

Hanna lists these items with the HI758: sample cuvettes with caps, a marine calcium reagent starter kit for 25 tests, a 1 mL syringe with tip, a minipipette with tip, a plastic pipette, a 1.5V AAA battery and the manual. You also need deionized or distilled water that has no calcium in it.

Hanna's product page warns about water. RODI water from a home filter may not be suitable for this test, because calcium can pass through filter membranes. Hanna says to use pure vapor distilled water for the first stage, and never to rinse cuvettes with tap water or saltwater, because calcium left in the cuvette raises your result.

Hanna calcium checker instructions, step by step

  1. Turn it on. Press the ON/OFF button. All segments show for a few seconds, then the display shows "Add", "C.1" with "Press" blinking.
  2. Prepare the zero cuvette. Add 1 mL of HI7581 Marine Calcium reagent A to the cuvette with the 1 mL syringe. Use the plastic pipette to fill the cuvette to the 10 mL mark with deionized water. Replace the cap and invert 3 to 5 times to mix.
  3. Zero the checker. Wipe the cuvette dry, insert it, and close the cap. Press ON/OFF. When the display shows "Add", "C2" with "Press" blinking, the checker is zeroed.
  4. Add your sample and reagent B. Remove the cuvette and unscrew the cap. Use the minipipette to add 0.1 mL of tank water. Add the contents of one packet of HI7582 Marine Calcium reagent B. Replace the cap.
  5. Shake and wait. Shake vigorously for 15 seconds, or until the powder is completely dissolved. Then let air bubbles dissipate for 15 seconds before you take a reading.
  6. Read. Insert the cuvette, close the cap, and press ON/OFF. The display shows calcium in ppm. The checker turns off 2 minutes after the reading.

Using the 0.1 mL minipipette

The 0.1 mL sample is small, so Hanna's manual gives exact steps for the minipipette.

  1. Attach the tip. Fit the pipette tip, then press the button down to the first stop.
  2. Draw the sample. Put the tip about 2 to 3 mm into the liquid. Let the button come back up slowly, and wait 2 seconds.
  3. Dispense. Touch the tip to the inside wall of the cuvette. Press down slowly to the first stop and wait until all the liquid is out. Then press to the second stop to clear what is left.

Hanna's page adds one more tip: make sure no extra tank water sits on the outside of the tip. Only the water drawn into the tip should go in the cuvette.

Tips for a better reading

  • Keep debris out of the sample.
  • The outside of the cuvette must be dry and free of fingerprints, oil and dirt. Wipe it with a microfiber cloth or a lint-free cloth before it goes in the checker.
  • Shaking makes bubbles, and bubbles raise the reading. Swirl the cuvette or tap it gently to clear them.
  • Do not let the reacted sample stand too long after adding reagent, because accuracy drops.
  • Pour the sample out right after you read it. The glass can stain for good if you leave it.

After the test, the cuvette has to dry clean before the next one. The CuveDry Hanna cuvette drying rack holds each cuvette upright to air dry.

What the error messages mean

  • Light High: too much ambient light reaches the detector. Check how you prepared the zero cuvette.
  • Light Low: not enough light for a reading. Check the zero cuvette.
  • Inverted Cuvettes: the sample and zero cuvettes are swapped. Swap them back and repeat.
  • Under Range: a blinking "200" means the sample reads below the lower limit. Check the steps and use the same cuvette for zero and measurement.
  • Over Range: the top value blinks. Check for debris, dilute the sample, and test again.
  • Battery Low or Drained Battery: replace the 1.5V AAA battery, negative end first.

Older kits use a different procedure

Hanna's older manual (06/11) lists a dropper and two 1 mL syringes instead of a minipipette. It adds 0.1 mL of sample with a syringe and uses a 15 second shake as well. If your kit has two syringes and no minipipette, follow the manual in your box.

What calcium reading should you aim for?

Sources differ. Bulk Reef Supply's calcium guide gives 350 to 450 ppm. Reef Builders (2020) gives 380 to 450 ppm, and Red Sea's table runs from 410 to 465 ppm depending on tank type. Pick the range your supplement or salt maker uses.

Questions people ask

How much sample does the Hanna calcium checker use?

0.1 mL of tank water, added with the minipipette after the checker is zeroed. The cuvette itself holds 10 mL once reagent A and deionized water are in it.

Can I use RODI water for the first stage?

Hanna says RODI water from home filtration units may not be suitable, because calcium can get through filter membranes. It points to pure vapor distilled water instead.

What does "Add C.2" mean?

It means the checker has zeroed. Remove the cuvette and add your sample and reagent B.

What is the range of the HI758?

200 to 600 ppm, with 1 ppm resolution and accuracy of plus or minus 6 ppm plus or minus 5% of the reading at 25 C.

Gear for this job

Keep your calcium test kit in one place

The Hanna Calcium Test Kit Organizer is a 3D-printed organizer for the Hanna Instruments calcium checker, made to fit the components of the kit. CuveDry holds Hanna Checker cuvettes upright to air dry.

Shop Hanna checker organizers
Back to blog