How to Frag Duncan Coral
Share
Quick answer
To frag Duncan coral, cut between polyps and cut each branch well below the polyp, through the skeleton and not the flesh. One experienced hobbyist leaves about an inch of skeleton below the polyp. Duncan flesh is sensitive and infects easily, so keep the coral wet and dip the frags afterward.
| Who | Reef keepers with a Duncan (whisker coral) colony large enough to split. |
|---|---|
| What | Cutting a branch or a few polyps free through the skeleton, then mounting the piece. |
| When | When the colony is big enough to have spare skeleton below the polyps. One forum author says that if you can see flesh inside the skeleton at the cut, you are too close. |
| Where | In a bucket of water from the coral's own tank, so you can rinse away loose flesh. |
| Why | To share a piece, thin out a colony, or move polyps to a new spot. |
What a Duncan is
Duncanopsammia axifuga is a large polyp stony coral. Wikipedia says the colony branches at irregular intervals, and each polyp is 2 to 3 cm across. Its common names include whisker coral and duncan coral. It says hobbyists propagate it by separating polyps from the base.
What you need
- A cutting tool. The forum author cuts with a band saw and says a Dremel works well on most hard corals. Bulk Reef Supply says torches, hammers and Duncans can be cut with coral cutters or pruners, and that a diamond band saw suits thick skeletons.
- A bucket of water from the coral's tank
- Saltwater tinted light amber with iodine, to cool the blade (one hobbyist's method)
- A dip for finished frags
- Coral glue and frag plugs or rubble
- Gloves and eye protection, which Reef Builders and Gensou list for other LPS corals
How to frag Duncan coral, step by step
- Keep it wet. Hold the colony in water from its home tank. Keep it fully submerged during handling until the polyps retract. Bulk Reef Supply says to make polyps retract before removing LPS corals from the water.
- Choose the cut. Cut between polyps. For a tight bunch, cut along the ridges that separate the polyps.
- Cut low. Cut each branch as far below the polyp as you can. The forum author says at least one inch is usually enough room. Bulk Reef Supply says to cut at the base of a branch and pick a healthy stem.
- Cool and rinse. The same author uses iodine-tinted saltwater as the cooling liquid for the blade. It says this disinfects cuts and improves survival. Rinse loose flesh away with tank water.
- Dip. That author soaks frags in a dip, naming Brightwell Aquatics Restor as the one he uses, to minimize flesh loss. Use any dip as its label says. Read our dipping guide first.
- Mount. Bulk Reef Supply says frags are attached to a plug, a coral mount or a piece of rubble. See How to Mount Coral the Right Way for glue steps.
Between colonies, rinse and refill your soak buckets so loose flesh from different corals does not mix.
A note from research
A 2017 study in the journal Aquaculture (Tagliafico and others) tested Duncanopsammia axifuga. About 85% of fragments survived across all treatments. Fragments that started with no polyps made the most new polyps. The authors called the species suitable for coral aquaculture. This was a farm study, not a home guide, but it suggests even a piece with no polyps can be worth keeping.
Aftercare
Wikipedia says Duncans need low to moderate light and flow, and do best placed low in the tank on the substrate or a low rock. It also says target feeding can add to their natural food. Keep the water stable while a frag heals, and check the cut area for tissue loss.
Mistakes to avoid
- Cutting so close to the polyp that you can see flesh in the skeleton.
- Letting the coral sit out of water during the cut.
- Reusing soak water between colonies.
- Placing a frag high in the tank, since Wikipedia says Duncans do best low in the tank.
Questions people ask
Is Duncan coral hard to frag?
The skeleton is dense, and one forum author says the flesh is sensitive and infects easily when damaged. So the method matters more than speed.
Can I snap a Duncan branch by hand?
The sources we read use a saw, Dremel or cutters. We did not find a source that recommends snapping Duncan branches.
Can I frag just one polyp?
Wikipedia says hobbyists separate polyps from the base. The 2017 study also grew polyps from fragments with none.
Do Duncans sting?
Wikipedia says the tentacles carry stinging cells that feel sticky on contact. Gloves are a reasonable precaution.
Gear for this job
Holders for fresh frags
The Nexus Single page describes a single plug holder for a prized frag or a new coral you want to test. The Nexus Nano holds 5 standard frag plugs and locks each plug in place. The Frag Steady is a sand-based stand made to prevent tip-overs.
Shop Frag RacksKeep reading: How to Frag Coral at Home: A Beginner's Guide · How to Frag Torch Coral
Sources
- Reef Central forum: Fragging 101, Duncan Coral
- Marine Aquarium Society of Colorado forum: Duncan Fragging 101
- Bulk Reef Supply: How to Frag and Mount Coral
- Wikipedia: Duncanopsammia
- Southern Cross University: A new technique to increase polyp production in stony coral aquaculture using waste fragments without polyps
- Reef Builders: Introduction to Hammer Coral Care
- Gensou: How to Frag LPS Corals, Splitting Torch, Hammer and Frogspawn



