Black Scoly Steady angled stand

How to Frag Torch Coral

Quick answer

To frag torch coral, cut through the bare skeleton of a branch, never through the fleshy polyp. Leave each piece a head and enough skeleton to mount. Wear gloves and eye protection, because Euphyllia tentacles can sting, then dip the cut frag and glue it to a plug.

Who Reef keepers with a healthy, branching torch colony with more than one head.
What Cutting a branch so one head, or a few, can grow on their own.
When When the colony is healthy. One source says not to frag unhealthy or stressed colonies. Wait until there is a clean section of bare skeleton to cut.
Where In a shallow tray of tank water, with clean saltwater ready to rinse.
Why To share a frag, move a head to a new spot, or give a crowded colony room.

How a torch coral is built

Torch coral (Euphyllia glabrescens) is a branching large polyp stony coral. Practical Fishkeeping says every polyp and corallite has its own branch. You cut the branches, not the corallites, ideally where bare skeleton shows. Gensou describes the branching Euphyllia pattern as Y-shaped.

Safety

Wear gloves and eye protection. Gensou says Euphyllia tentacles can sting strongly, and skeletal dust clouds the water when you cut. Keep clean saltwater ready for rinsing. Handle frags gently and do not touch the fleshy polyps.

What you need

  • Gloves and safety goggles
  • A cutting tool (see below)
  • Tank water in a shallow tray, plus clean saltwater for rinsing
  • An iodine dip
  • Coral glue and frag plugs, or live rock rubble

Sources disagree on tools. Gensou prefers a Dremel with a diamond cutting disc and says bone cutters only suit thin branches and can crush the skeleton. Practical Fishkeeping says hand, pliers or a diamond band saw all work. Bulk Reef Supply says coral cutters or garden pruners can cut torches at the base of a branch. A crushed stalk can hurt the polyp, so match the tool to how thick the branch is.

How to frag torch coral, step by step

  1. Get the polyps to retract. Bulk Reef Supply says to make polyps retract before taking the coral out of the water, which matters most for LPS corals like Euphyllia. Retracted polyps also let you see the skeleton.
  2. Turn off the flow. Gensou says to turn off all flow and move the colony to a shallow tray of tank water.
  3. Pick the cut. Gensou says to cut at least 1.5 cm below the point where two heads split, so each piece keeps a head and enough skeleton to mount. It says never to cut through fleshy tissue. If there is no clean skeleton, wait for more growth.
  4. Score and snap. With a Dremel at medium speed, score a line around the branch. Rotate the colony, not the tool, and use light pressure. Snap the branch by hand once the score is deep enough. Gensou aims for under 30 seconds per head.
  5. Dip right away. Gensou uses an iodine dip for five minutes right after cutting. Use the time on your own dip's label. See our dipping guide.
  6. Mount. Dry the cut end briefly, then glue the frag to a plug or a piece of live rock rubble. Our mounting guide covers glue.

Aftercare

For the first week, Gensou says to use low to moderate flow and indirect light. Tentacles typically extend within 48 hours of a clean cut. Bare skeleton takes four to six weeks to be covered over, and new heads often appear two to three months after healing. Gensou feeds small meaty foods such as mysis two to three times a week.

If brown jelly disease appears, Gensou says to remove the frag, scrub off the infected tissue with a soft toothbrush, dip it again and quarantine it.

For placement, Practical Fishkeeping suggests about halfway up the tank with at least medium flow, and a perimeter of about 10 cm (4 inches) because torches can extend a tentacle to about double its length and sting neighbors. Saltwater Aquarium Blog says at least 6 inches. Give more space as the colony grows. For ideas on spacing, see aquascaping with magnetic frag mounts.

Mistakes to avoid

  • Cutting through the fleshy part of the polyp.
  • Using bone cutters on a thick branch.
  • Cutting a stressed or sick colony.
  • Skipping gloves and eye protection.
  • Putting the frag next to a neighbor it can sting.

Questions people ask

Can I frag a torch with bone cutters?

Maybe, on thin branches. Gensou warns they can crush the skeleton on thicker ones, and Bulk Reef Supply says cutters can cut torches at the base of a branch.

Where exactly do I cut?

Through the branch where bare skeleton shows, below where two heads split. Gensou gives at least 1.5 cm.

Do torch corals sting?

Sources say yes, or at least that they can sting neighbors with extended tentacles. Wear gloves.

How long until a frag looks normal?

Per Gensou, tentacles usually extend within 48 hours. New heads often come two to three months after healing.

Gear for this job

A place to show a torch frag

The Scoly Steady page says it is designed to show Scolymia, Acanthophyllia and Euphyllia, with a 20 degree pitch. The PhotoBooth page says it is for torches, Euphyllia, zoanthids and mushrooms. The Frag Steady Tallboys page describes a 4 inch stand that raises coral higher in the water column.

Shop Frag Racks
Back to blog