Black Scoly Steady angled stand

How to Frag Hammer Coral

Quick answer

How to frag hammer coral depends on its growth form. Branching hammers are the easy case: cut through the bare skeleton of a branch, not the flesh. Wall hammers are harder, leave a large wound and are open to infection, so sources treat them with more caution. Wear gloves and eye protection for both.

Who Reef keepers with a settled hammer coral, branching or wall form, who need a frag or more room.
What Cutting a head or branch from the colony and mounting it on a plug or rubble.
When When the coral is healthy. For a new arrival, Reef Builders says to wait 2 to 3 days before dipping.
Where In a shallow tray of tank water with sterile tools, gloves and eye protection.
Why To share a frag, give a crowded colony space, or move a head to a new spot.

Branching or wall: check which you have

Reef Builders describes two forms. Branching hammers are the more common type. They grow fairly fast, and the heads and flesh are well separated, so you can usually snip them apart without cutting tissue. Wall hammers grow slowly and usually come as colonies. Reef Builders says they can be harder to frag, but not impossible.

If you are not sure, do not cut yet. Look at the skeleton and the space between heads first. If you cannot find a clean section of bare skeleton, wait for more growth.

Safety and sweeper tentacles

Hammers have tentacles that reach past the colony and can sting nearby corals, as Reef Builders and Sunnyside Corals both say. Wear gloves, since Euphyllia tentacles can sting strongly, and wear eye protection because cutting kicks up skeletal dust. Reef Builders also says to use sterile tools. Keep clean saltwater ready to rinse.

What you need

  • Gloves and safety goggles
  • A Dremel with a diamond cutting disc, or a band saw for dense skeletons
  • Bone cutters, only for thin branches
  • A shallow tray of tank water
  • An iodine dip
  • Coral glue and a frag plug or live rock rubble

How to frag hammer coral, step by step

  1. Let the polyps retract. Bulk Reef Supply says to make polyps retract before taking Euphyllia out of the water. Gensou says to turn off all flow and work in a shallow tray of tank water.
  2. Find the cut. Reef Builders says to cut through the thinnest part of the skeleton to minimize cutting. For branching hammers, Gensou says to cut at least 1.5 cm below the point where two heads diverge, and never through fleshy tissue.
  3. Score and snap. Gensou scores a line around the branch with a Dremel at medium speed. Rotate the colony, use light pressure, then snap the branch by hand. Aim for under 30 seconds per head.
  4. Dip. Reef Builders says to dip wall hammer frags in iodine because the wound is large and slow to heal. Gensou uses an iodine dip for five minutes right after cutting. Follow your dip's label. See our dipping guide.
  5. Mount. Dry the cut end briefly, then glue the frag to a plug or rubble. See How to Mount Coral the Right Way.
  6. Place it with flow. Reef Builders says to put fresh frags in adequate flow to help healing. Gensou suggests low to moderate flow and indirect light for the first week.

Wall hammers: go slower

Gensou says wall-type LPS are usually better left whole unless a colony is very large or partly dying. If you must split one, it uses a band saw, or scores along a natural skeletal seam with a Dremel. It says wall frags need longer recovery because more tissue is exposed. Reef Builders says to use sterile tools and gloves, and to dip afterward.

Aftercare and spacing

Gensou says tentacles typically extend within 48 hours of a clean cut. Bare skeleton takes four to six weeks to cover over, and new heads often appear two to three months after healing. It feeds small meaty foods such as mysis two to three times a week. Reef Builders says to spot feed and avoid broadcast feeding.

Give hammers room. Sunnyside Corals says to leave at least 3 to 4 inches from other coral species. Sources agree on low to moderate flow. Light numbers differ: Reef Builders says about 100 to 150 PAR, and Sunnyside Corals says 100 to 250. Move the coral around until it opens fully. For help with layout, see aquascaping with magnetic frag mounts.

Mistakes to avoid

  • Cutting through flesh instead of bare skeleton.
  • Using bone cutters on a thick skeleton.
  • Splitting a wall hammer when you do not have to.
  • Skipping the dip on a large wound.
  • Placing frags where tentacles can reach other corals.

Questions people ask

Is hammer coral easy to frag?

Branching hammers are, per Reef Builders. Wall hammers are harder but not impossible.

What tool should I use?

Gensou prefers a Dremel with a diamond disc. A band saw suits dense skeletons. Bone cutters only suit thin branches.

Do hammer corals sting?

Yes. Reef Builders and Sunnyside Corals say they can sting nearby corals, and Gensou says Euphyllia tentacles can sting strongly.

How long before a frag looks normal?

Gensou says tentacles usually extend within 48 hours, with full coverage of exposed bone in four to six weeks.

Gear for this job

Stands and displays for hammer frags

The Scoly Steady page says it is designed to show Euphyllia, among other corals. The PhotoBooth page names Euphyllia too. The Frag Steady page says it is a sand-based frag stand made to prevent tip-overs.

Shop Frag Racks
Back to blog